Ecosyste.ms: Awesome
An open API service indexing awesome lists of open source software.
https://github.com/gjashley/CYD-ESPHome-Sensors
Sample ESPHome YAML for CYD with BME680, PMSA003i i2c sensors and SH1106 i2c display
https://github.com/gjashley/CYD-ESPHome-Sensors
Last synced: 15 days ago
JSON representation
Sample ESPHome YAML for CYD with BME680, PMSA003i i2c sensors and SH1106 i2c display
- Host: GitHub
- URL: https://github.com/gjashley/CYD-ESPHome-Sensors
- Owner: gjashley
- License: mit
- Created: 2024-01-05T01:24:11.000Z (6 months ago)
- Default Branch: main
- Last Pushed: 2024-01-05T23:17:42.000Z (6 months ago)
- Last Synced: 2024-02-24T14:33:47.417Z (4 months ago)
- Size: 81.1 KB
- Stars: 2
- Watchers: 2
- Forks: 0
- Open Issues: 0
-
Metadata Files:
- Readme: README.md
- License: LICENSE
Lists
- awesome-stars - gjashley/CYD-ESPHome-Sensors - Sample ESPHome YAML for CYD with BME680, PMSA003i i2c sensors and SH1106 i2c display (Others)
README
# CYD-ESPHome-Sensors
**CYD Temperature and Air Quality Monitor for ESPHome**
1. **Set up your CYD in ESPHome as usual use this yaml (after editing it with your setup)**
2. **Create a folder named fonts in your ESPHome folder and copy the file fonts/lucon.ttf there.**
Although we're using ESPHome to set-up, all the sensors are local, so it doesn't rely on any HA devices for data, it doesn't even pull the time from HA ... so it _should_ operate outside of your HA network. It _will_ appear as a device in Home Assistant with ALL the data, so you can create dashboards, charts etc to your heart's content.
**PARTS:**
These are the sensors I used, but you should be able to substitute any i2c sensor/device as long as it is supported in ESPHome and you use the appropriate configuration [https://esphome.io/components/sensor/](https://esphome.io/components/sensor/)
1. CYD ESP32-2432S028R - The base single USB unit, I didn't test it on any other variant.
2. BME680 i2c Temperature, Humidity, Pressure and Gas Sensor
I used Adafruit's breakout board [https://www.adafruit.com/product/3660](https://www.adafruit.com/product/3660).
3. PMSA003i i2c Air Quality Sensor
I used Adafruit's breakout board [https://www.adafruit.com/product/4632](https://www.adafruit.com/product/4632).
Make sure you get the PMSA003_ **i** _, the _ **i** _ stands for i2c (other versions use UART)
4. SH1106 i2c 0.96" OLED Display (optional - I just wanted to see if it worked)
These are very common, I think I got a bunch from our favorite overseas electronic supplier, they also have them at our favorite mega online store.
5. JST MX 1.2mm 4 pin male to female Dupont connector - like the one which came with your CYD
6. JST SH 4 pin 1.0mm 4 pin male (STEMMA QT) to male Dupont connector
[CYD -\> F/M Dupont -> BME680 STEMMA QT in]
7. JST SH 4 pin 1.0mm 4 pin male (STEMMA QT) to JST SH 4 pin 1.0mm 4 pin male (STEMMA QT)
[BME680 STEMMA QT out -> PMSA003i STEMMA QT in]
8. JST SH 4 pin 1.0mm 4 pin male (STEMMA QT) to female Dupont connector - my SH1106 had male headers already installed.
[PMSA033i STEMMA QT -> SH1106]
NOTE: All my cables had the same color scheme, but that's not always the case, check all the pins match:
VCC - **RED**
GND - **BLACK**
SCL - **YELLOW**
SDA - **BLUE**
I haven't thought about a case, because I don't have a (functional) 3d printer, I'll probably just screw it together with layers of that acrylic 'case' that you sometimes get with the CYD. I may shorten, re-terminate or solder some of the connections, I have a non-stemma BME680 board which was cheaper lying around, you can get a bare PMSA003i, but it likes 5v and the Adafruit board has a boost converter
I'd like to try other sensors, and if I have time, I can look at adding display graphics … or maybe even graphs!
Any ideas or suggestions would be gratefully received,
OK, I think that's about it for now.
Boom Shanka
**Gareth**
