https://github.com/FPGAwars/Alhambra-II-FPGA

:star2: Alhambra II FPGA board
https://github.com/FPGAwars/Alhambra-II-FPGA

alhambra-ii-fpga fpga fpga-board icestorm-toolchain opensource opensource-toolchain

Last synced: about 1 month ago
JSON representation

:star2: Alhambra II FPGA board

• Host: GitHub
• URL: https://github.com/FPGAwars/Alhambra-II-FPGA
• Owner: FPGAwars
• License: lgpl-3.0
• Created: 2018-04-20T10:02:23.000Z (over 6 years ago)
• Default Branch: master
• Last Pushed: 2023-10-22T10:56:05.000Z (about 1 year ago)
• Last Synced: 2024-04-16T22:26:25.567Z (8 months ago)
• Topics: alhambra-ii-fpga, fpga, fpga-board, icestorm-toolchain, opensource, opensource-toolchain
• Homepage:
• Size: 28.5 MB
• Stars: 77
• Watchers: 15
• Forks: 27
• Open Issues: 5
• Metadata Files:
  • Readme: README.md
  • License: LICENSE

Awesome Lists containing this project

• awesome-latticeFPGAs - Alhambra II

README

        
# Alhambra II FPGA board

Open FPGA for makers

![](https://github.com/FPGAwars/Alhambra-II-FPGA/raw/master/wiki/V1.0/Alhambra-II-01.jpg)

## Features

* iCE40HX4K (Lattice) FPGA development board (8K using opensource toolchain)

* Open hardware

* Compatible with the opensource [icestorm toolchain](Compatible with the opensource icestorm toolchain) and [Icestudio](https://github.com/FPGAwars/icestudio)

* Arduino like board: similar pinout than Arduino one

* You can Reuse most of available shields

* Control your robots / printbots from an FPGA

* FTDI 2232H USB device allows FPGA programming and UART interface to a PC

* ON/OFF electronic switch (turn off your mobile robot easily, switching on does not overload your USB port)

* 8 general purpose LEDs (user LEDs)

* 2 general purpose pushbuttons

* 32Mb flash memory for up to 30 bitstreams or user data

* 20 Input/output 3.3V (5V tolerant) pins

* All I/O pins include 200 ohms serial resistors for direct LED activation

* 4-Channels, 12 bits A/D converter

* Cold boot pins accessible from GPIO

* Switching regulators for high frequency processing at low power input

* 12 MHZ MEMS oscillator

* Reset pushbutton

* USB power supply, two connectors (up to 4.8A)

* Power pins and I/O pins allow permanent shortcircuit

## Documentation

[The proyect documentation is located in the wiki](https://github.com/FPGAwars/Alhambra-II-FPGA/wiki)

## Author

* [Eladio Delgado Mingorance](https://twitter.com/EladioDM)

## Credits

* Alhambra II V1.0 Board was derived from the [Icezum Alhambra V1.1 board](https://github.com/FPGAwars/icezum)

## License

![](https://github.com/FPGAwars/icezum/raw/master/wiki/attribution-share-alike-creative-commons-license.png)

Licensed under [Creative Commons Attribution-ShareAlike 4.0 International License](http://creativecommons.org/licenses/by-sa/4.0/)