Ecosyste.ms: Awesome
An open API service indexing awesome lists of open source software.
https://github.com/azholtikov/esp-now-window-door-sensor
ESP-NOW based window/door sensor for ESP8266. Alternate firmware for Tuya/SmartLife WiFi window/door sensors.
https://github.com/azholtikov/esp-now-window-door-sensor
esp-now esp8266 home-assistant iot smartlife tuya
Last synced: about 23 hours ago
JSON representation
ESP-NOW based window/door sensor for ESP8266. Alternate firmware for Tuya/SmartLife WiFi window/door sensors.
- Host: GitHub
- URL: https://github.com/azholtikov/esp-now-window-door-sensor
- Owner: aZholtikov
- Created: 2023-01-06T09:54:54.000Z (almost 2 years ago)
- Default Branch: main
- Last Pushed: 2023-03-15T12:52:31.000Z (over 1 year ago)
- Last Synced: 2023-07-25T05:49:02.128Z (over 1 year ago)
- Topics: esp-now, esp8266, home-assistant, iot, smartlife, tuya
- Language: C++
- Homepage:
- Size: 19.2 MB
- Stars: 2
- Watchers: 1
- Forks: 0
- Open Issues: 0
-
Metadata Files:
- Readme: README.md
Awesome Lists containing this project
README
# ESP-NOW window/door sensor for ESP8266
ESP-NOW based window/door sensor for ESP8266. Alternate firmware for Tuya/SmartLife WiFi window/door sensors.
## Features
1. When triggered transmits system information, battery level charge and sensor status (OPEN/CLOSED).
2. Average response time of 1 second (depends on the MCU of the sensor).
3. In setup/update mode creates an access point named "ESP-NOW window XXXXXXXXXXXX" with password "12345678" (IP 192.168.4.1).
4. Automatically adds sensor and battery configuration to Home Assistan via MQTT discovery as a binary_sensor (for sensor) and sensor (for battery).
5. Possibility firmware update over OTA (if is allows the size of the flash memory).
6. Web interface for settings.
## Notes
1. ESP-NOW mesh network based on the library [ZHNetwork](https://github.com/aZholtikov/ZHNetwork).
2. For enter to setup/update mode press the button for > 5 seconds. The LED will illuminate. Access point will be available during 120 seconds before the module is powered off.
## Tested on
See [here](https://github.com/aZholtikov/ESP-NOW-Window-Door-Sensor/tree/main/hardware).
## Attention
1. A gateway is required. For details see [ESP-NOW Gateway](https://github.com/aZholtikov/ESP-NOW-Gateway).
2. ESP-NOW network name must be set same of all another ESP-NOW devices in network.
3. If encryption is used, the key must be set same of all another ESP-NOW devices in network.
4. Upload the "data" folder (with web interface) into the filesystem before flashing.
5. For using this firmware on Tuya/SmartLife WiFi window/door sensors, the WiFi module must be replaced with an ESP8266 compatible module (if necessary).
6. Highly recommended connect an external power supply during setup/upgrade.
7. Because this sensor is battery operated, it has an additional controller (MCU) that controls the power of the WiFi module (Module) and transmits data to it for transmission to the network. The communication is done via UART at 9600 speed. Make sure that the protocol is correct before flashing. Details [here](https://github.com/aZholtikov/ESP-NOW-Window-Door-Sensor/tree/main/doc).
Any feedback via [e-mail](mailto:[email protected]) would be appreciated. Or... [Buy me a coffee](https://paypal.me/aZholtikov).