Ecosyste.ms: Awesome

An open API service indexing awesome lists of open source software.

Awesome Lists | Featured Topics | Projects

https://github.com/cctweaker/ESPsensor

Temperature, humidity and air pressure sensor with blazing fast ESP-Now communication.
https://github.com/cctweaker/ESPsensor

air-pressure bme280 dewpoint esp-01 esp-01s esp-now esp8266 humidity si7021 temperature

Last synced: about 1 month ago
JSON representation

Temperature, humidity and air pressure sensor with blazing fast ESP-Now communication.

Awesome Lists containing this project

README 

        
# ESPsensor

is covering a need for low power, cheap, battery operated sensors that you can place throughout your house.

It is designed to use an ESP-01 / ESP-01S and a SI7021 temperature and humidity sensor. BME280 sensors are also supported and add air pressure readings (real and normalized).

Communication is done through ESP-Now protocol to save a huge amount of power compared to regular WiFi.

It needs a ESP-Now Gateway to receive the data and forward it to MQTT.



# Sensors supported

- SI7021 for temperature, humidity, dew point

- BME280 for temperature, humidity, dew point, pressure, normalized pressure



# Features

- perfect for infrequent small data transmissions

- no need for full blown WiFi, connects and transmits data instantly (172ms total wake time)

- much faster than other solutions that rely on Wifi (about 8-10 seconds, while secure MQTT takes about 15-20 seconds)

- much faster transfer speed compared to other 2.4GHz protocols

- lower total power consumption, great for battery operated sensors/buttons

- uses a parallel network for IoT without hoarding your DHCP leases in WiFi (just the gateway is connected)



# Build

Clone in PlatformIO or download archive and extract main source folder to your Arduino projects folder.

Libraries will be automatically fetched in PlatformIO, for Arduino check below for the needed libraries.



# Setup

Rename example_private.h to private.h and edit to you liking.



# Info

Boards like NodeMCU and WeMos D1 can not measure ADC_VCC (their own voltage) because the ADC pin is connected to a voltage divider. To measure ADC_VCC the ADC pin must be floating like in ESP-01, ESP-07 and ESP-12 modules.



# Hardware

Roll your own based on the schematics inside hardware folder or get the PCB (with or without components) from 3DStar.ro ESPsensor PCBs



# Deep Sleep Mod

ESP-01 and ESP-01S do not have GPIO 16 available. To use them for deepsleep a small mod is necessary. GPIO 16 is nicely exposed on the bottom-left side of the ESP8266 chip. All we need to do is bridge it with a wire to RESET pin.

Pictures are available in the project's hardware folder.



# Message format

ESPsensor sends a message with the following format: {"t":"ESPsensor","v":2.01,"ID":"abcdef","vcc":3482,"tmp":27.02,"hum":54.74,"dew":17.14,"prs":998.08,"prn":1008.54}

- t: device type, value can be sensor, switch or anything else, depending on firmware

- v: firmware version

- ID: ESPid, last 3 bytes of the ESP's mac address in hex format, unique per ESP chip

- tmp: temperature reading

- hum: humidity reading

- dew: dew point estimation

- prs: air pressure reading (only for BME280 sensor)

- prn: normalized (sea level) air pressure reading as reported in North America (only for BME280 sensor)

- vcc: raw value of ESP voltage



# Raw voltage

To show correct ESP voltage, measure voltage after the regulator (should be 3.29 - 3.31) and calculate the correction factor.

F = vin/measured voltage

F should be between 1024 - 1086. Apply the correction in NodeRed for example. Works just fine until about 2.9V. Best to change/charge batteries when voltage falls below 3.00V.



# Libraries

Si7021 by Felix Rusu


BME280_Light by zen



# Plans

- add more sensor types